Farm Lighting

Telehandler Lights: Work Lights, Beacons, and Road Lighting Explained

By Agri Lighting team Published Updated 12 min read

Telehandler Lights: Work Lights, Beacons, and Road Lighting Explained
In this guide
  1. Why Telehandler Lighting Is Different From Tractor Lighting
  2. Boom Lights: Lighting the Load and the Lift Height
  3. Chassis and Cab Roof Work Lights
  4. Beacons and Amber Warning Lights for Telehandlers
  5. Road-Legal Lighting for Telehandlers Driven on UK Roads
  6. Lighting by Manufacturer: JCB, Manitou, Merlo, Claas
  7. LED Upgrade Routes for Older Telehandlers
  8. Wiring and Switching for Added Telehandler Lights
  9. What to Buy First If You Are Upgrading a Telehandler

A telehandler lighting setup combines boom-mounted work lights, chassis and cab roof lights, an amber warning beacon, and a full set of road-legal lamps for public-road travel. A modern factory-built telehandler usually comes with several work lights, at least one beacon, and a complete road lighting kit. Older machines often run with 2 to 4 halogen work lights and need an LED upgrade to match the visibility of a current Loadall, MLT, or Scorpion. This guide covers every light fitted to a telescopic handler, where it goes, what it has to do, and how UK law treats the machine on the public road.

Why Telehandler Lighting Is Different From Tractor Lighting

A telehandler boom changes the lighting demand. The boom carries the load between 0 and 10 metres above the ground, and the operator needs visibility on the load itself, not just on the area around the machine. A tractor lights the field ahead. A telehandler lights the load above and the work zone alongside.

Three structural differences set a telehandler apart from a tractor for lighting purposes.

The first is the boom itself. The boom extends and retracts, lifts and lowers, and tilts the load through 90 degrees or more. Lights mounted on the chassis or cab roof can only follow the load up to a certain angle. Above that angle the load shadows the work. Boom-mounted lights solve the problem because they travel with the load.

The second is the side-on working pattern. A telehandler often loads or unloads from the side, parallel to a wall, trailer, or stack. The operator works from the cab looking sideways or upward, not just forward. Side and rear chassis lights become more important on a telehandler than on a tractor.

The third is yard use. Telehandlers spend more hours on hard-surface yards, near pedestrians, near other vehicles, and near buildings. Beacon visibility and reverse lighting carry more weight than on a tractor that mostly works in fields.

For the broader machinery lighting context, see Lighting for Farm Machinery: Beyond the Tractor.

Boom Lights: Lighting the Load and the Lift Height

Boom lights mount on the boom itself and travel with the load. They are the single most important upgrade on any telehandler used after dark.

Many factory-built machines carry boom lights as standard or as an option, typically two or more. The exact number varies by make, model, specification and year, so check the parts list for the machine before ordering.

Mount boom lights at the boom head, near the carriage, and angle them slightly downward so the beam covers the load and the area immediately below it. A 4,000 to 6,000 lumen LED flood per light covers a stack or trailer side at full lift. Use IP69K-rated lights because the boom takes the full force of pressure-washing during clean-down and the rear of the lamp lives in dust and debris from forks, buckets, and grabs.

Anti-vibration brackets matter on a boom. The boom whips through the air every time the load drops or the carriage tilts, and a hard-mounted lamp can crack its LED chips or driver. Rubber-isolated brackets, sold by every reputable lamp brand, greatly extend lamp life.

Boom light wiring runs through a coiled cable along the boom or through an internal cable run inside the boom section. Manufacturer-fitted looms use the internal route. Aftermarket installations almost always use the external coiled cable. Use a heavy-duty Deutsch connector at the boom-to-chassis junction so the cable can be unplugged for boom service.

Aim the boom lights at the carriage and 1 to 2 metres beyond. Aiming further out throws light past the working zone and creates glare back to the cab through the boom-mounted load.

Chassis and Cab Roof Work Lights

Chassis and cab roof work lights light the area around the machine, including the wheels, the rear, the sides, and the working zone in front of the boom.

A complete telehandler chassis lighting setup uses six positions. The numbers below assume a single LED flood per position and give a typical lumen target.

Position Purpose Lumen target
Front grille left Forward and left forward 3,000 to 5,000
Front grille right Forward and right forward 3,000 to 5,000
Cab roof front Long-range forward 5,000 to 8,000
Cab roof rear Reversing and rear monitoring 4,000 to 6,000
Side cab pillar Side-on loading view 3,000 to 5,000
Rear chassis low Hitch, drawbar, low rear view 3,000 to 5,000

Total chassis output sits between 21,000 and 34,000 lumens for a complete setup, on top of the boom light output of 8,000 to 24,000 lumens. A full LED telehandler with boom lights, chassis lights, and cab roof lights runs between 30,000 and 60,000 lumens of working illumination.

Use a flood beam pattern for all six positions. A spot pattern wastes light beyond the work area on a telehandler because the operator rarely looks more than 30 metres ahead during loading work. Reserve combination beam patterns for cab roof front lights only, and only on machines that travel between yards or move at speed across long sites.

For lumen and beam-pattern fundamentals, see Work Light Beam Patterns: Flood, Spot, and Combo Explained.

For mounting bracket selection, see How to Mount Work Lights.

Beacons and Amber Warning Lights for Telehandlers

A telehandler used on a yard or near road traffic needs an amber beacon. The beacon warns pedestrians and other vehicle operators that a slow, wide, articulating machine is in the work area.

Under regulation 17 of the Road Vehicles Lighting Regulations 1989, a motor vehicle with four or more wheels and a maximum design speed of 25 mph or less must show an amber beacon when it uses an unrestricted dual carriageway (speed limit over 50 mph). Most telehandlers are built for 40 km/h (24.85 mph), so they are caught. On other roads a beacon is not a general legal requirement, but it is allowed, and wise, whenever it is necessary or desirable to warn others of the vehicle, which covers most road moves of a slow, wide machine.

Three beacon types fit telehandlers.

A DIN pole beacon mounts on a 28 mm or 25 mm pole, fixed to the cab roof rear or the cab front roof rail. This is the standard factory fitment on JCB Loadall, Manitou MLT, and Merlo Roto machines. The beacon sits above the cab profile and projects 360 degrees of warning light.

A magnetic beacon clamps to any flat metal surface on the cab roof through its magnetic base. This is the right choice for a telehandler used on the road occasionally, where a permanent fitment would be over-specified. Magnetic beacons run from a coiled cable into the cab cigarette lighter socket or through a hard-wired feed to the auxiliary panel. See magnetic beacons for more, or the beacon range for current options.

A flexi DIN beacon uses a sprung-spring mount that bends on impact with branches or low overhead structures. Telehandlers that work in or near orchards, polytunnels, or grain stores benefit from a flexi mount because rigid poles snap under contact. The beacon flexes back to vertical without damage to the pole or the beacon itself.

Choose an ECE R65 approved beacon for any road-going telehandler. UK law (RVLR Schedule 16) sets the basics: lamp centre at least 1,200 mm above the ground, light visible from all round, and 60 to 240 flashes per minute. It does not require an R65 mark, but R65 is the recognised standard for warning lamp performance and good practice to buy. R10 EMC approval matters separately, especially on telehandlers built after 2010 with electronic engine management or telematics. A non-EMC beacon can cause warning lights on the dash, false fault codes, or interference with the load chart display. See ECE R65 Beacons for the full standard.

Telehandlers used near pedestrians benefit from a second beacon at the rear of the cab roof. A second amber beacon doubles the visibility from behind during reverse moves and means the warning continues if one beacon fails.

A telehandler driven on the UK public road needs the same lighting as a slow-moving agricultural vehicle. The Road Vehicles Lighting Regulations 1989 set the requirement.

The usual road lighting kit is listed below. Some items are exempt on slow machines (for example, stop lamps are not required on a vehicle with a maximum speed of 25 mph or less, and indicators are not required at 15 mph or less), but any lamp that is fitted must work.

Component Quantity Position
Dipped-beam headlight 2 Front, symmetrical
Front position lamps (sidelights) 2 Front, symmetrical
Rear position lamps (taillights) 2 Rear, symmetrical
Brake lights 2 Rear, symmetrical
Direction indicators 4 Front and rear, both sides
Hazard warning system n/a Operates the indicators together
Number plate light 1 Illuminates the rear plate

End-outline marker lamps are required on wider, faster motor vehicles, but a vehicle with a maximum speed of 25 mph or less is exempt, which covers most 40 km/h telehandlers. Many owners fit them anyway on wide machines.

Reflectors complete the road-legal kit. A telehandler needs red rear reflectors at the back. Amber side reflectors are required on motor vehicles over 6 metres long, but not on a vehicle with a maximum speed of 25 mph or less. The triangular shape is reserved for trailers; on the telehandler itself use a non-triangular red reflector.

Headlights on a telehandler must dip to the left for UK use. Continental machines imported from France or Germany may have headlights aimed for right-hand traffic, and these need adjustment or replacement before UK road use.

For the full UK lighting law, see Road Vehicles Lighting Regulations 1989 and Tractor Road Legal Lights.

Lighting by Manufacturer: JCB, Manitou, Merlo, Claas

Each major telehandler brand fits a different factory lighting kit. The differences matter when buying replacement parts or planning an upgrade.

JCB Loadall is the dominant telehandler brand in the UK. Current Loadall AGRI models come with LED lighting packages, boom lights on many specifications, an amber beacon, and a complete road-legal kit; check the exact fit for the model and year. Older Loadall models from the 526, 530, 535, and 541 series were typically halogen, and these are the machines most commonly upgraded to LED. See JCB Telehandler and Loadall Lights for the full fitment guide.

Manitou MLT models fit LED lighting on many current machines, while older machines are typically halogen. The MLT 625, 730, 840, and 960 cover the agricultural range. Manitou uses a different boom cable routing from JCB, with an internal cable run on most boom sections.

Merlo Multifarmer models are often specified with more boom lights than average. The Merlo Multifarmer doubles as a tractor and a telehandler, and its lighting kit includes everything needed for full road use plus PTO-driven implement work after dark.

Claas Scorpion telehandlers are built in partnership with Liebherr and share component design with Liebherr construction telehandlers. The Scorpion 732, 736, 741, 746, and 756 models use LED lighting throughout on the current series. Older Scorpion machines fitted halogen.

JLG, Genie, and other plant-focused telehandler brands appear on UK farms in smaller numbers. These machines often come with a plant-specification lighting kit that meets construction site requirements but may need additional rear road-lighting for full UK agricultural road use.

LED Upgrade Routes for Older Telehandlers

An older telehandler fitted with halogen work lights upgrades to LED with little effort and immediate benefit.

Three reasons drive the LED upgrade on a telehandler.

The first is power draw. A pair of 70-watt halogen work lights pull 12 amps from the alternator at full brightness. A pair of LED work lights at the same lumen output pull 4 to 5 amps. The difference matters because telehandlers often run multiple work lights, a beacon, and reversing lights at the same time, and an old alternator struggles to keep the battery charged under that load.

The second is vibration tolerance. Halogen filaments break under continuous high-frequency vibration, so a boom-mounted halogen lamp often fails far short of its rated life. An LED lamp on the same mount lasts many times longer.

The third is light output. A modern 60-watt LED work light delivers 5,000 to 6,000 lumens. A 70-watt halogen delivers 1,500 to 1,800 lumens. The LED produces three times the visible light at the same physical size and lower power draw.

EMC compliance matters for any LED upgrade on a telehandler built after 2010. Non-EMC LEDs interfere with the engine ECU, the load monitoring system, and any GPS or telematics fitted to the machine. Check for the R10 marking on every LED lamp before fitting it to a modern telehandler. For the full picture on EMC compliance, see Do LED Lights Interfere with GPS and Auto-Steer Systems.

For LED work light selection, see LED work lights and What Are LED Work Lights and Why Are They Replacing Halogen.

Wiring and Switching for Added Telehandler Lights

Added lights wire through a relay back to the cab switch panel or auxiliary fuse panel. Wiring direct from the battery without a relay overloads the cab switch contacts and risks fire.

A standard relay-based wiring layout for added telehandler lights uses six components.

A 30-amp automotive relay sits in a sealed plastic housing, ideally inside the cab or under a sealed bonnet section. The relay carries the high-current feed from the battery to the lights.

A fused supply runs from the battery positive to the relay. A 30-amp blade fuse sized for the total light load sits within 300 mm of the battery. Use waterproof fuse holders on a telehandler because the chassis sees mud, water, and pressure-wash spray.

A switched trigger feed runs from a cab switch (or from the existing work light switch) to the relay coil. This low-current feed turns the relay on and off without carrying the full lamp load.

A heavy-gauge cable runs from the relay output to the lights. Use 4 mm² cable for loads up to 20 amps and 6 mm² for loads up to 30 amps. Run the cable through existing cable looms or use a separate split conduit to protect it from chafing.

Deutsch connectors at every junction prevent water ingress and corrosion. A telehandler that lives outdoors and gets pressure-washed weekly will corrode any standard automotive connector inside two years. Deutsch connectors hold up for the life of the machine.

A common ground point on the chassis completes the circuit. The ground point should be a bolted earth tag, bare metal under the bolt, with the cable terminated in a ring crimp.

For the full wiring guide, see How to Wire Work Lights to a 12V System with a Relay.

What to Buy First If You Are Upgrading a Telehandler

A telehandler upgrade in priority order looks like this.

Boom lights come first. The boom lights deliver the biggest single visibility gain because they light the load, and the load is what the operator is paying attention to. Two LED boom lights at 5,000 lumens each transform an old machine.

Cab roof rear comes second. The cab roof rear light makes reversing safe in any work environment with traffic, pedestrians, or stacked product. A single 6,000 lumen LED is enough.

Beacon comes third if the machine does not already have one. An ECE R65 LED beacon on a magnetic or DIN pole mount meets the beacon requirement for unrestricted dual carriageways and gives the practical visibility for yard work and other road moves.

Side cab pillar lights come fourth. Side lights pay back fastest on telehandlers that load trailers, lorries, or stacks parallel to the cab.

Cab roof front and front grille lights come last. These are the most expensive to add because of the wiring run, and the existing factory fitment usually does enough.

A complete LED upgrade for a 10-year-old telehandler runs between £400 and £900 in parts depending on lamp brand and quantity, plus 4 to 8 hours of fitting time. The result is a machine that lights its work as well as a current Loadall or MLT.

For the full machinery lighting context, see the machinery lighting hub and the related guide on Combine Harvester Lighting.

AL

Written by the Agri Lighting team

Agri Lighting is an independent UK tractor lighting specialist based in Lincolnshire, from a parts business that has supplied farms, contractors and dealers since 1996. Our guides are written from the questions our counter and phone staff answer every week. Something not covered? Call 01522 440522 or email [email protected].